danaxgps.blogg.se - Windows 10 atmel usb cdc driver

#Windows 10 atmel usb cdc driver install#
#Windows 10 atmel usb cdc driver serial#
#Windows 10 atmel usb cdc driver driver#

For Microsoft Windows users: Install USB drivers for Atmel and Segger tools.

In fact, the Atmel EDBG (Embedded Debugger) chip on the Evaluation Kit acts as a serial-to-USB converter and is loaded with a firmware that is able to talk USB-CDC protocol.

#Windows 10 atmel usb cdc driver serial#

You can also access the serial console through the on-board serial-to-USB converter. Using the micro-A USB connector (J20 EDBG-USB) usb 1-1.1.2: FTDI USB Serial Device converter now attached to ttyUSB0 The /dev/ttyUSBx number will be used to configure the terminal emulator.

For Linux users: Identify the serial USB connection by monitoring the last lines of dmesg command.

The COMxx number will be used to configure the terminal emulator.

For Microsoft Windows users: Identify the USB connection that is established, USB Serial Port should appear in Device Manager.

Place it properly according to the silkscreen and connect the cable to the board (J1)

Be sure to connect a 3.3V compatible cable and identify its GND pin.

FTDI-based ones are the most popular, have a look to this page to get the driver:

#Windows 10 atmel usb cdc driver driver#

For Microsoft Windows users: Install the driver of your USB TTL serial cable.

Using DBGU on TTL-to-USB connector (DEBUG J1) One is from the DBGU port with the help of a TTL-to-USB serial cable (marked as DEBUG J1), another is from micro-A USB connector that gives access to the on-board serial-to-USB converter (marked as J20 EDBG-USB). The DBGU serial console can be accessed from two connectors. usb 1-1.1.2: FTDI USB Serial Device converter now attached to ttyUSB0 A /dev/ttyUSB0 node has been created. usb 1-1.1.2: Endpoint 2 MaxPacketSize 64 usb 1-1.1.2: Endpoint 1 MaxPacketSize 64 ftdi_sio 1-1.1.2:1.0: FTDI USB Serial Device converter detected usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1.1.2: New USB device found, idVendor=0403, idProduct=6001 usb 1-1.1.2: new full-speed USB device number 17 using ehci-pci The /dev/ttyUSBx or /dev/ttyACMx number will be used to configure the terminal emulator. For Linux users: identify the USB connection by monitoring the last lines of dmesg command.Connect a DB9 serial cable to the J11 connector.The DBGU serial console can be accessed from the RS-232 connector (marked as DBGU J11). Connect the USB cable to the board (J14 – JTAG and USB Serial DBGU).In fact, the Cortex-M3 chip underneath the Evaluation Kit acts as a serial-to-USB converter and is loaded with a firmware that is able to speak USB-CDC. You can access the serial console through the on-board serial-USB converter. The /dev/ttyACMx number will be used to configure the terminal emulator.Īccess the console - sama5d3xek Evaluation Kit JLink CDC UART Port should appear in Device Manager. For Microsoft Windows users: identify the USB connection that is established.Connect the USB cable to the board (J22 OB-JLink).Choose (2-3) for JP19 and JP20 jumper settings.No need to install a driver on any regular Linux distribution. For Microsoft Windows users: Install the J-Link CDC USB driver.You can also access the serial console through the on-board serial-USB converter. Using the micro-A USB connector (J22 OB-JLink) Now open your favorite terminal emulator with appropriate settings.Connect a DB9 serial cable to the J24 connector.Choose (1-2) for JP19 and JP20 jumper settings.The JP19 and JP20 jumpers are used to select which port is used to access DBGU serial console. One is from the RS-232 connector (marked as DBGU J24), another is from micro-A USB connector that gives access to the on-board serial-USB converter (marked as J22 OB-JLink). The usual serial communication parameters are 115200 8-N-1 : sama5d2 revision A, only to access the ROMCode through serial interface and see the RomBOOT message appearing, configure your serial line to 57600.Ĭhange it back to 115200 for normal operation.Īll components and demo binaries are now configured to work at 115200 8-N-1.Access the console on JLINK micro-A USB connector (J16).Using DEBUG on TTL-to-USB connector (DEBUG J26).Access the console - sama5d27_wlsom1_ek.Using the micro-B USB connector (J22 VBUS_JLINK).Using DEBUG on TTL-to-USB connector (DEBUG J24).Access the console on JLINK micro-A USB connector (J9).Access the console on JLINK micro-A USB connector (J10).Using the micro-A USB connector (J14 EDBG-USB).Using DEBUG on TTL-to-USB connector (DEBUG J1).Access the console on DEBUG serial port.Using the micro-A USB connector (J20 EDBG-USB).Using DBGU on TTL-to-USB connector (DEBUG J1).Using the micro-A USB connector (J22 OB-JLink).